Clean & Lubricate a RIDGID K-45 Drain Machine: Drum Takedown, Cable Clean, and Reassembly
I'm Ricky Cox, master plumber with Sewer Studs Plumbing & Drain. The RIDGID K-45 drum cable machine is a very popular small drain cleaning tool — plumbers use it all across the nation. It's great for cleaning out lavatory drains, waste arms, tub drains, shower drains — basically your smaller drains — and it's a great tool to have on the truck.
It's also a tool that gets neglected. The cable on the machine in this video is rusted and pretty beat up, and I'll tell you who didn't maintain it very well: me. This is the quick maintenance takedown and clean — how to take the drum out, clean it, lubricate the cable, and put everything back together. It's also the same order of operations you'd use if you need to change out the cable.
What You Need
You only need two tools to do this:
- A flathead screwdriver — I've got my handy Milwaukee flathead here.
- A good lubricant — WD-40, or my personal favorite, PB Blaster.
Step One: Loosen the Four Screws
The machine has four screws on the shell. Loosen those four screws — you don't have to take the screws all the way out. Just get them loose enough that you can tell the outside shell is loosened up.
Step Two: Twist the Front Off and Pull the Drum Assembly Out
Give the top piece a counterclockwise turn while holding the body, and then just pull the front part of the machine out.
Now you can see the drain cable in the drum. On this machine the cable had kind of crossed over on itself, so I'm taking the whole thing out: get all of the cable out of the drum, then stretch the cable out across the shop so you can work on it.
Set the cable out with the end of the cable — the end that has the bulb on it — facing away from you.
Step Three: Dump the Debris Out of the Drum
Take the drum and empty out all the debris. You'd be surprised what accumulates in there. Once it's dumped, it's nice and clean inside.
Before I feed the drain cable back in, I like to squirt a little bit of PB Blaster in the drum, just to kind of clean things up.
Step Four: Feed the Cable Back In — Clockwise Head, Lubricant Every Few Wraps
There's a direction the cable has to go in. When you're feeding the cable, you want to make sure the head ends up in the clockwise position.
Feed the cable in like this:
- The cable doesn't have to go in super tight, but I do recommend feeding it top to bottom.
- Every three or four wraps around, give it a nice squirt of lubricant — that cleans and coats the cable as it goes in.
- Extra lubricant won't hurt it. PB Blaster is not your enemy — it's your friend.
When the cable is all the way in, give it one last spray, put a rag over the top, and shake the lubricant around. You want those drain cables nice and saturated with lubricant.
Step Five: Reassemble — Tabs, a Foot of Cable, Clockwise Turn, Snug the Screws
Pop the front piece back in — you'll see how the little tabs line up. Keep the end of your cable about a foot out; that's all you need, just about a foot. Lubricate that end section while you're at it.
Then line up the screws, give the top piece a clockwise turn, and tighten the four screws back down — snug her down.
Last thing, as promised: shoot some lube into the top section of the machine. And that's it — you're all done.
How Often Should You Do This?
I recommend doing this every 3 to 6 months, or whenever you notice your cable starts to feel like it's really fighting you in the drum. A cable fighting you is a cable telling you it's dry, dirty, or both — and a rusted, crossed-over cable like the one on this machine is what happens when the interval gets skipped.
When the Problem Is the Drain, Not the Machine
This maintenance is about keeping a small drain machine ready for lavatories, waste arms, tubs, and showers. When a clog keeps coming back, or the line in trouble is bigger than a small branch drain, that's a different job: our drain cleaning page covers how we clear drains across Tampa Bay, our hydro-jetting 101 guide explains when a jetter beats a cable, and our grout and concrete removal post shows what a cable machine is up against when the wrong material gets into a line. For a stubborn kitchen branch, see the double-sink drain fix.
Frequently Asked Questions
How often should a RIDGID K-45 cable be cleaned and lubricated?
Every 3 to 6 months — or whenever you notice the cable starts to feel like it's really fighting you in the drum. That fighting feeling is the maintenance reminder.
Do the four shell screws have to come all the way out to open the machine?
No. Loosen the four screws just enough that the outside shell is loosened up, then give the top piece a counterclockwise turn while holding the body and pull the front part out.
Which way does the cable feed back into the drum?
There's a direction the cable has to go in: the head has to end up in the clockwise position. Feed it top to bottom, not super tight, and squirt lubricant in every three or four wraps.
Can you use too much lubricant on the cable?
No — it's not going to hurt it if you have extra lubricant in there. After the last wrap, give it one final spray, cover the drum with a rag, and shake it around so the cables are nice and saturated.
Is this the same process for changing the cable out entirely?
Yes. Taking the drum out and cleaning it is the same order of operations you'd use if you need to change out the cable — the takedown, the drum, and the reassembly are identical.
How much cable do you leave out when you reassemble?
About a foot. Keep the end of the cable about a foot out as the front piece goes back on and the tabs line up, then line up the screws and turn clockwise to close it.
Need a Drain Cleared Instead?
If your drain is the one fighting you — a lavatory, tub, or shower drain that keeps clogging — we'll give you a straight answer and a firm quote. Call Sewer Studs Plumbing & Drain at (813) 680-2284, Monday through Friday, 8 AM to 5 PM. We serve homeowners across Tampa Bay — see our Tampa plumber page.